由于電蒸汽鍋爐http://m.tsgspipe.cn/等大型鍋爐一般用于工業生產或者是工業用水的熱交換設備，體積一般比家用蒸汽鍋爐體積較大，所以在安裝過程中掌握平衡的問題就擺在了用戶的面前，那么蒸汽鍋爐在安裝過程中如何掌握平衡?

大型蒸汽鍋爐在安裝過程中保持左右平衡的方法可以從縱向、橫向兩方面入手，輕松幫您的蒸汽鍋爐找平。
Large steam boiler maintain about balancing methods during the installation process from vertical, horizontal two-pronged approach to help you easily steam boiler leveling.

電蒸汽鍋爐http://m.tsgspipe.cn/在南北方向找平的方法：先找到水平尺長不小于600毫米的尺子，將尺子水平放在蒸汽鍋爐爐排的縱排面上，治愈爐排前后兩處，要求爐排面縱向應水平或爐排面略坡向爐膛后部這樣可以很輕松的檢查到爐排面的縱向水平度。最大傾斜度小于等于10毫米.當蒸汽鍋爐縱向不平時，可用千斤頂將過低的一端頂起，在蒸汽鍋爐的支架下墊以適當厚度的鋼板，使蒸汽鍋爐的水平度達到要求。墊鐵的間距一般為500～1000mm。
Electric steam boiler in north-south direction leveling approach: first find a ruler-foot level of not less than 600 mm long, and the ruler placed horizontally on a vertical surface of a steam boiler drain grate, grate heal around two, require longitudinal grate surface should horizontal or grate furnace rear surface slope slightly so you can easily check the level of the grate longitudinal plane. The maximum gradient of 10 mm or less. When the steam boiler is not the usual portrait, can jack the low end of the top, in the steam boiler underlying stent to the proper thickness steel plate, so that the level of the steam boilers meet the requirements. Pitch horn is generally 500 ~ 1000mm.

電蒸汽鍋爐http://m.tsgspipe.cn/在東西方向找平的方法：先找到水平尺長不小于600毫米的尺子，將尺子水平放在蒸汽鍋爐爐排的橫排面上，治愈爐排前后兩處，爐排的橫向傾斜度不得大于5mm(爐排的橫向傾斜過大會導致爐排跑偏)。當爐排橫向不平時，用千斤頂將蒸汽鍋爐一側支架同時頂起，在支架下墊以適當厚度的鋼板，墊鐵的間距一般為500～1000mm。
Electric steam boilers in east-west direction leveling approach: first find a ruler-foot level of not less than 600 mm long, and the horizontal ruler placed horizontally on the surface of a steam boiler grate, cure around the grate two lateral inclination grate no larger than 5mm (lateral tilting grate grate over the General Assembly lead to deviation). When the grate laterally peacetime,the steam boiler with a jack from the top side of the bracket at the same time, the underlying stent to the proper thickness steel plate, horn spacing is generally 500 ~ 1000mm.